Diamond Polishing Pads

Grinding step of diamond polishing pad

The first step: rough grinding

In the rough grinding, we asked the Diamond Polishing Pads to have a deeper knife and a higher grinding efficiency. The grinding lines are thicker and the ground surface is rougher. The main role in the first step is to clarify the traces of the saw blade left by the marble in the previous process and to grind the flat surface of the stone in place.

The second step: fine grinding

The pattern, grain, color, etc. of the finely ground marble surface have been clearly shown, and the surface is finer and smoother, and the finely ground marble begins to have a weak gloss.

The third step: further fine grinding

The polished marble face has no visible marks, and the surface will be smoother and smoother, with a maximum of 55 degrees.

The fourth step: Polishing

After we have done the first few steps, we use a marble-specific polishing machine to grind the marble from 50-3000 grit stone water-grinding pieces from coarse to fine, so that the ground is bright and flat, after polishing and grinding. The marble surface is very bright, and the marble’s lightness can reach more than 85 degrees.

What is the scope of use of diamond polishing pads?

Granite

Marble

Quartz-stone

Ceramic-tile

Industrial-floor

Parking-lot-floor

Cement floor

Concrete-floor

Diamond Polishing Pads available equipment

√ Floor washing machine √ Grinding machine √ Polishing machine √ Hand grinding machine

Diamond polishing pads size parameters

4-inch-diamond-polishing-pads

5-inch-diamond-polishing-pads

6-inch-diamond-polishing-pads

Center hole diameter
0.630 inches
The thickness of the grinding discs are
3mm.5mm.6mm, 8mm, 12mm.
The colors are
gray, black, yellow, burnt yellow, red, pink, green, blue, white.

Diameter (metric)
80mm, 100mm.125mm.350mm.
The thickness of the grinding discs are
3mm.5mm.6mm, 8mm, 12mm.
Material:
Diamond resin / nylon cloth

How to choose diamond polishing pads？

The correct choice according to the purpose is of great significance to reduce the processing cost. When choosing, first consider the following elements:

1
You can observe the color of the surface of the cutting head. Under normal circumstances, the color of the cutting head should be silver-white, and it also has the natural color of iron. If it is a poor quality blade, it will look more because it contains other impurities. The comparison is dark and not shiny.
2
Observe how much particles are on the diamond grinding disc. If it is inferior diamond grinding disc, it will be cheaper in cost, which will mainly reduce the content of soft grinding disc to reduce the cost. After the choice, the consumer will not only have no way. Work, and the consumption of diamond discs is also very fast.
3
Feel the rhythm of the whole cut. If you choose a high-quality cutting piece, it will be smoother during the whole cutting process. If the cutting piece is not suitable, the feeding speed will be faster, resulting in faster cutting. Blade wear is more serious.
4
Because the inferior diamond grinding disc is made of corundum, the biggest difference between diamond and corundum is that the degree of wear resistance of the whole abrasive grain is different. If diamond is used to process into a saw blade, then the service life is used. Will be longer.

How to use diamond polishing pads to renovate marble floors

Marble lightly refurbished The stone surface is slightly scratched, it can be refurbished with a light refurbishment process. If there is old wax on the ground, wax it first, and then use 800# diamond polishing pad and clean water for ten minutes.

Note: Add water during the polishing process to keep the ground moist, and use a water suction machine to suck up the sewage to prevent the sewage from polluting the ground for the second time.

Change to 1500# and 3000# diamond polishing pads and polish them one by one using the above method. After all the renovation procedures are completed, wash with clean water and absorb the water on the stone surface, and the marble light renovation work is completed.

Moderate renovation of marble When the surface of the stone loses its luster, it can not reflect the object at all but there is no excessively deep scratches, it can be refurbished with a moderate renovation process. Use 200#, 400#, 800#, 1500#, 3000# diamond polishing pads to polish one by one. The polishing method and precautions are consistent with the above.

Deep renovation of marble When the stone surface has holes, weathering, severe corrosion, complete loss of luster and deep scratches, the deep renovation process can be used for renovation. Before refurbishing, repair the holes first, as follows:

First clean the dirt in the hole, and then dry the stone. According to the color and reflective characteristics of the original stone, use imported epoxy resin or unsaturated resin glue, and then repair it after coloring. Use a weighting machine and turn it. The new disc and 50#, 150#, 200#, 400#, 800#, 1500#, 3000# diamond polishing pads are polished one by one. The polishing method and precautions are the same as those for light renovation.

Welcome to visit our website, if you have any questions, please feel free to contact us or leave us a message.

contect us

Diamond Polishing Pads